Get a Quote

How to Ensure your Physical Data Sanitization Equipment meets the NIST 800-88 requirements

November 18, 2026 · Insights · NIST SP 800-88

← News & Events

Close-up of a circuit board from recovered electronics

Short answer: To make sure physical data sanitization equipment meets NIST SP 800-88, show that it achieves the destroy outcome for every media type you handle and that you can prove it. Map each media type to a machine, check the output and the NSA Evaluated Products List, maintain and calibrate the equipment, record each run and train operators.

A shredder or crusher does not make a facility compliant on its own. What matters is whether the equipment actually achieves the outcome NIST SP 800-88 calls destroy for every type of media you handle, and whether you can prove it. This guide walks through how to check your physical data sanitization equipment against NIST SP 800-88, the NSA Evaluated Products Lists and, for R2 facilities, SERI R2v3 Appendix B.

To check the source directly, read the full NIST SP 800-88 Rev. 2 (PDF) from NIST.

What NIST SP 800-88 Rev. 2 means by “destroy”

NIST published SP 800-88 Revision 2 in September 2025. It supersedes Revision 1 (December 2014). Both revisions use three sanitization methods: clear, purge and destroy. Revision 2 defines the destroy method this way:

“Destroy sanitization techniques render target data recovery infeasible using state-of-the-art laboratory techniques and results in the subsequent inability to use the ISM for the storage of data.”

NIST SP 800-88 Rev. 2, Sec. 3.1.3

NIST lists disintegrate, incinerate, melt, pulverize and shred as the physical techniques commonly associated with destroy. It also warns that bending, cutting, or drilling a hole through a device “may only partly damage” it, leaving portions accessible in a laboratory. Drilling a hole through a drive should not be treated as destruction on its own.

One change from Revision 1 matters for equipment buyers. Revision 1’s Appendix A gave media-by-media tables of sanitization techniques, and many shop-floor procedures still point to it. Revision 2 removed those tables and replaced technique and tool details with recommendations to comply with IEEE 2883 (see our IEEE 2883 data sanitization training), NSA specifications, or an organizationally approved standard. If your procedures still cite Revision 1’s Appendix A, plan to update them. See what changed in NIST SP 800-88 Rev. 2.

Extra requirements for R2v3 facilities (Appendix B)

For electronics recyclers and ITAD facilities certified to R2v3 (see our R2 recycling standard (R2v3) explained), the R2 Standard sets its own requirements. Its definition of sanitization, in summary:

Under R2v3, sanitization means removing and destroying the data held on a data storage device so it cannot be recovered with commonly available software or techniques. It covers both logical and physical destruction of that data, and it also requires taking off every user label and marking and clearing activity logs. The right method depends on the device; the standard gives examples such as software overwriting, degaussing, shredding, incineration, disintegration, grinding and embossing.

Summary of SERI R2v3, Definitions (Sanitization), p. 9

When data storage devices are sanitized physically, Appendix B allows three ways to destroy them:

  1. A destruction method that Table 1 of Appendix B lists for that type of device.
  2. The NSA Storage Device Sanitization Manual, carried out with equipment that appears on NSA’s Evaluated Products List.
  3. Another physical destruction method, provided a competent expert has independently verified that it sanitizes effectively.

Summary of SERI R2v3, Appendix B – Data Sanitization, requirement (7), p. 27

Table 1 gives a method and an expected result for each type of device. For hard drives and solid state storage, in summary:

Our summary of R2v3 Appendix B, Table 1 (hard drives and solid state storage only)
DeviceMethodExpected result
Magnetic hard disk drivesDegauss and crushBoth are required: the drive is degaussed and crushed in a hard drive crusher
Shred or otherwise physically destroyThe platters end up in fragments
IncinerateThe drive is melted down to metal
Solid state storage (for example SIM cards, SDRAM, flash drives, boards with non-volatile flash memory, SSDs, phones and tablets)Shred or disintegrateThe memory chips end up in fragments
CrushUses an SSD crusher built for crushing chip sets
IncinerateBurned to ash

Any degausser used must carry the manufacturer’s rating for the type of media it is used on.
Summarized from SERI R2v3, Appendix B – Data Sanitization, Table 1, p. 28. The full table also covers magnetic tape, diskettes, optical disks, hard copy and other media.

Appendix B adds two more requirements on physical destruction:

  • If a customer, a legal requirement or the sensitivity of the information calls for a stricter destruction method, the facility has to apply whichever requirement is strictest.
  • Video of all physical destruction of media has to be kept for a minimum of 60 days.

Summary of SERI R2v3, Appendix B – Data Sanitization, requirements (8) and (9), p. 28

The R2v3 passages above are Paradygm Consulting’s summaries of SERI’s R2 Standard Version 3.0 (R2v3), effective July 1, 2020, pp. 9 and 27–28, not the standard’s wording. Use the full standard and SERI’s current guidance, and confirm interpretations with your certification body.

For help applying Appendix B, see R2v3 certification consulting.

How to verify destruction equipment meets NIST 800-88: 7 steps

1. Map every media type to a method and a machine

List each kind of media you accept: hard drives, SSDs and NVMe drives, phones and tablets, flash drives and memory cards, circuit boards with flash memory, tape, optical disks and paper. For each one, record the sanitization method (clear, purge or destroy), the machine you use and the output you expect. A hard drive shredder that is right for platters may not reduce SSD or phone memory chips to fragments.

2. Verify shred and crush output against your criteria

Compare what actually comes out of the machine with your written criteria: platters in fragments, memory chips in fragments, media burned to ash. NIST notes that as data density and material hardness increase, some destructive techniques become ineffective, and that pulverize and shred techniques for ISM should be avoided for anything but the lowest security categories of data. Set your particle-size or fragment criteria to match the sensitivity of the data and any stricter customer or legal requirement.

3. Check your model on the NSA Evaluated Products List (EPL)

The NSA publishes Evaluated Products Lists (EPLs) for equipment such as hard disk drive destruction devices, magnetic degaussers, optical sanitization devices and solid state disintegrators. NSA updates the lists as needed and also publishes an expired products list. If your procedure relies on the NSA route, confirm that your exact model is on the current list and keep a dated copy with your records.

4. Degaussers: purge, not destroy, under NIST Rev. 2

NIST Revision 2 says degaussing “is not considered an approved destroy sanitization technique” and treats it as a physical purge technique for legacy magnetic media. It also notes that many existing degaussers lack the force to degauss higher-coercivity media, and that degaussing an SSD sanitizes no data. Under R2v3 Table 1, a degausser needs the manufacturer’s rating for the media it is used on, and hard drives on that route need both degaussing and crushing.

5. Calibrate, maintain and test each machine

NIST’s guidance for a sanitization policy includes equipment calibration, testing and maintenance. It also lists equipment that is “not approved and/or improperly calibrated” among the things that call the effectiveness of sanitization into question. Keep maintenance logs, blade or cutter inspections, and periodic output checks for each machine.

6. Verify, validate and document each run

NIST Revision 2 separates verification (the technique completed without errors) from validation (the organization reviews the results and approves the sanitization as effective). Its example certificate of sanitization records the media details, method, technique, tool used, verification method and the people who verified it. R2 facilities certified to Appendix B also need the video recordings required by Appendix B (9).

7. Train equipment operators and verifiers

Equipment is only as reliable as its operators. NIST includes personnel competencies, skills and training in a sanitization policy, and R2v3 Appendix B requires data sanitization workers to be trained and evaluated on the methods they are authorized to perform. Keep training records for everyone who operates or verifies the equipment. Start with our NIST SP 800-88 training, quiz and certificate.

Frequently asked questions

Does owning a shredder or crusher make a facility NIST 800-88 compliant?

No. A shredder or crusher does not make a facility compliant on its own. The equipment has to achieve the outcome NIST SP 800-88 calls destroy for every type of media you handle, and you need records that prove it.

Is degaussing a destroy method under NIST SP 800-88 Rev. 2?

No. NIST SP 800-88 Rev. 2 says degaussing is not considered an approved destroy sanitization technique and treats it as a physical purge technique for legacy magnetic media. Many existing degaussers lack the force for higher-coercivity media, and degaussing an SSD sanitizes no data.

Is drilling a hole through a hard drive enough to destroy it?

Not on its own. NIST warns that bending, cutting or drilling a hole through a device may only partly damage it, leaving portions accessible in a laboratory.

Does NIST SP 800-88 Rev. 2 still include the Appendix A media tables?

No. Revision 2 removed the media-by-media tables from Revision 1's Appendix A and instead recommends complying with IEEE 2883, NSA specifications or an organizationally approved standard. Procedures that still cite Revision 1's Appendix A should be updated.

How do I check whether my destruction equipment is on the NSA Evaluated Products List?

The NSA publishes Evaluated Products Lists for equipment such as hard disk drive destruction devices, degaussers, optical sanitization devices and solid state disintegrators, and updates them as needed. Confirm your exact model is on the current list and keep a dated copy with your records.

What records should I keep for each destruction run?

NIST SP 800-88 Rev. 2 separates verification from validation. Its example certificate of sanitization records the media details, method, technique, tool used, verification method and the people who verified it. Also keep maintenance logs, cutter inspections, output checks and operator training records.

Related NIST 800-88 resources

Sources

Last updated: November 18, 2026. Commentary by Paradygm Consulting. Not a substitute for NIST SP 800-88, IEEE 2883, NSA guidance or the R2v3 Standard.

← Back to News & Events